Zoom F8 Multi-Track Field Recorder with PCF-8 Protective Case

Zoom F8 Multi-Track Field Recorder

RECORDING MEDIA

• Dual SD card slot supports:
• 16 MB–2 GB SD cards
• 4 GB–32 GB SDHC cards
• 64 GB–512 GB SDXC cards

INPUTS: 1-8

• Connectors: XLR/TRS combo jacks (XLR: 2 hot, TRS: TIP hot)

INPUTS: XLR (MIC)

• Input gain: +10 – +75 dB
• Input impedance: 3.3 kΩ
• Maximum input level: +14 dBu (at 0 dBFS, limiter ON)
• Phantom power: +24/+48V 10mA maximum for each channel THD (Total Harmonic Distortion): 0.009% max (1kHz, 22Hz-22kHz BW, Input Gain min, -10dBu input)

INPUTS: TRS (LINE)

• Input gain: −10 – +55 dB
• Input impedance: 28 kΩ
• Maximum input level: +34 dBu (at 0 dBFS, limiter ON)
• THD (Total Harmonic Distortion): 0.010% max (1kHz, 22Hz-22kHz BW, Input Gain min +10dBu input)

INPUTS: ADDITIONAL INFO

• Equivalent input noise: −127 dBu or less (A-weighted, +75 dB input gain, 150Ω input)
• Frequency characteristics: 10 Hz – 80 kHz +0.5 dB/−1 dB (192 kHz sampling rate)
• A/D dynamic range: 120 dB typ (−60 dBFS input, A-weighted)
• Crosstalk: −90 dB or less (between adjacent channels, 1 kHz)
• MIC IN: ZOOM mic capsule input (use disables Inputs 1/2)
• SLATE MIC: Built-in mic for voice memos can freely be assigned to tracks

OUTPUTS: MAIN OUT 1/2

• Connectors: TA3 connectors, balanced output (2: hot)
• Output impedance: 150 Ω or less
• Reference output level: −10 dBV (Normal Output Type), −40 dBV (Mic Output Type), 1 kHz, 600Ω load
• Maximum output level: +10 dBV (Normal Output Type), −20 dBV (Mic Output Type), 1 kHz, 600Ω load

OUTPUTS: SUB OUT 1/2

• Connector: 3.5 mm stereo mini unbalanced output jack
• Output impedance: 100 Ω or less
• Reference output level: −10 dBV (Normal Output Type), −40 dBV (Mic Output Type), 1 kHz, 10kΩ load
• Maximum output level: +10 dBV (Normal Output Type), −20 dBV (Mic Output Type), 1 kHz, 10kΩ load

HEADPHONE

• Connector: 1/4" unbalanced stereo output jack
• Output impedance: 15 Ω or less
• Maximum output level: 100 mW + 100 mW (32Ω load)

D/A

• D/A dynamic range: 106 dB typical (−60dBFS input, A-weighted)

RECORDING FORMATS: WHEN WAV SELECTED

• Supported formats: 44.1/47.952/48/48.048/88.2/96/192kHz, 16/24-bit, mono/stereo/2-10 ch poly, BWF and iXML Maximum simultaneous recording tracks: 10 (8 inputs + stereo mix) 8 (with 192 kHz sampling rate)

RECORDING FORMATS: WHEN MP3 SELECTED

• Supported formats: 128/192/320 kbps, 44.1/48 kHz, ID3v1 tags
• Maximum simultaneous recording tracks: 2

RECORDING TIME

• Using a 32GB card:
• 30:51:00 (48 kHz/24-bit stereo WAV)
• 7:42:00 (192 kHz/24-bit stereo WAV)

TIME CODE

• Connector: BNC
• Modes: Off, Int Free Run, Int Record Run, Int RTC Run, Ext, Ext Auto Rec (audio clock can be synchronized to timecode)
• Frame rates: 23.976ND, 24ND, 25ND, 29.97ND, 29.97D, 30ND, 30D
• Precision: ±0.2 ppm Supported input levels: 0.2 – 5.0 Vpp
• Input impedance: 4.6 kΩ Output level: 3.3 Vpp
• Output impedance: 50 Ω or less

POWER SUPPLIES

• Batteries: 8 AA
• AC adapter: AD-19 DC12V 2A (center plus)
• External DC power supply: HIROSE HR10A-7R-4S 4-pin connector (1 pin: −, 4 pin: +), 9–16 V

CONTINUOUS RECORDING TIME: WHEN RECORDING 2 CHANNELS AT 48KHZ/16-BIT WITHOUT HEADPHONES

• Alkaline batteries: 8.5 hours or more
• NiMH (2450mAh): 10 hours or more
• Lithium batteries: 12.5 hours or more

CONTINUOUS RECORDING TIME: WHEN RECORDING 8 CHANNELS AT 48KHZ/24-BIT WITH HEADPHONES

• Alkaline batteries: 4.5 hours or more
• NiMH (2450mAh): 6 hours or more
• Lithium batteries: 8.5 hours or more

CONTINUOUS RECORDING TIME: WHEN RECORDING 8 CHANNELS AT 192KHZ/24-BIT WITH HEADPHONES, PHANTOM POWER AND DISPLAY BACKLIGHTING

• Alkaline batteries: 1 hour or more
• NiMH (2450mAh): 2 hours or more
• Lithium batteries: 3 hours or more

DISPLAY

• 2.4" full-color LCD: 320x240

USB: MASS STORAGE OPERATION

• Class: USB 2.0 High Speed

USB: MULTITRACK AUDIO INTERFACE OPERATION (DRIVER REQUIRED FOR WINDOWS, NOT REQUIRED FOR MAC)

• Class: USB 2.0 High Speed
• Specifications: 44.1/48/96 kHz, 16/24-bit, 8-in/4-out

USB: STEREO MIX AUDIO INTERFACE OPERATION (NO DRIVER REQUIRED)

• Class: USB 2.0 Full Speed
• Specifications: 44.1/48 kHz, 16-bit, 2-in/2-out
• Note: iPad audio interface operation supported (Stereo Mix mode only)

EXTERNAL DIMENSIONS

• Main unit:
• 7.0 in. (W) × 5.5 in. (D) × 2.1 in. (H)
• 178.2 mm (W) × 140.3 mm (D) × 54.3 mm (H)

WEIGHT

• Main unit only: 2.1 pounds (960 g)

 Manufacturer's Description

Zoom F8 Multi-Track Field Recorder

Advances in video have made filmmaking accessible to creators everywhere. But the accessibility of professional audio devices has not kept pace. Field recorders, with essential features such as time code, have been unobtainable for most. Until now.

The F8 is made for serious filmmakers and sound designers. With 8-input/10-track recording, super low-noise preamps, and support for 24-bit/192 kHz audio, the F8 captures the highest-quality audio.

Mic pre's

Outfitted with our finest mic preamps to date, the F8 features an extremely low noise floor (−127 dBu EIN) and high gain (up to 75 dB), with +4 dB line inputs.

High-resolution audio and advanced limiters

The F8 can record at 24-bit/192 kHz resolution and is equipped with onboard limiters designed to provide overload protection. Limiting can be applied to all 8 channels simultaneously at full resolution, with 10 dB of headroom and controls for setting threshold, attack, and release.

Time code with pinpoint accuracy

The F8’s time code is state-of-the-art. It utilizes a Temperature Compensated Crystal Oscillator (TCXO) that generates time code at 0.2 ppm accuracy, enabling rock-solid syncing of audio and video.

The F8 supports all standard dropframe and non-drop formats, and can jam sync to time code being provided by external devices. An input and output are provided on standard BNC connectors, enabling easy integration into any rig.

Weight and build

The F8 is not only versatile and feature rich, it is the smallest field recorder with eight XLR combo preamps ever made. Weighing just 2.1 pounds (without batteries), its aluminum chassis is both rugged and durable.

Display

Sound professionals sometimes work in dusty, hard-to-see environments. Level meters with adjustable brightness and its 2.4 inch full-color backlit LCD (which can be set to monochrome mode), make the F8 easy to use in any environment — from low-light to direct sunlight.

File formats, resolution, and sample rates

The F8 records in BWF-compatible WAV format at 16 or 24-bit resolution, and at any standard sample rate up to 192 kHz. When recording files in MP3 format, you can choose bit rates of 128, 192, or 320 kbps.

FEATURES

The F8 provides every option you need to create professional field recordings:

• Phantom power (+24V/+48V) can be turned on and off for each preamp individually.
• Plug in any Zoom mic capsule.
• 10 tracks—8 input channels, plus a stereo mix track*—allow you to simultaneously record stereo and surround sound.
• An onboard mixer with flexible routing of all inputs and outputs (pre- and post-fader). Each channel has controls for pan, input/output delay, filtering, and limiting.
• The F8 can be mounted to a tripod and attached to your camera using the included mounting bracket.

* Stereo mix track not recorded when 192 kHz sampling rate is selected

Dual SD card recording

Record on two SD/SDHC/SDXC cards*, up to 512 GB each, simultaneously, allowing you to instantly backup or split recordings (for example, save eight tracks onto one card and a stereo mix onto another).

Three power sources

A 4-pin Hirose connector allows the use of external 9-16 volt DC battery packs. Internal power is provided by 8 AA batteries. The F8 can switch power sources from a DC battery pack to the AA batteries at a user-defined voltage level for uninterrupted recording. You can also use the supplied 12 volt AC adapter when not on the go.

File protection

Files are saved periodically during recording. This provides an extra level of protection in the event of unexpected file interruption, for example, power loss or the removal of an SD card.

Dual-channel recording

The F8’s dual-channel recording mode allows you to create safety tracks on inputs 1-4, each with independent level, limiting, delay, phase inversion, and high-pass filtering.

Pre-record

The pre-record function allows you to capture up to 6 seconds of audio before you hit the RECORD button.

Comprehensive headphone monitoring

Out in the field, it's important to be able to quickly check levels as you're recording. With the F8, it's simple. A single display lets you monitor single or multiple tracks, as well as any of the Main or Sub outputs, via a dedicated ¼" headphone jack with a front panel volume control.

Signals can be freely routed to the left and/or right headphone channels, pre- or post-fader, and the headphone output can be switched to mono. You can set headphone alert tones for low battery, recording start/stop, or recording errors.

The F8 comes equipped with a built-in 100 mW headphone amplifier, allowing you to monitor in the noisiest of environments.

A first in the field

The F8 is the first field recorder to come with wireless Bluetooth control. The Zoom F8 Control App for iOS provides extensive wireless remote control of the F8 from your iPhone, iPad, or iPod Touch (5th Gen) using Bluetooth LE protocol. Functions include Record, Play, Stop, Fast-Forward, and Rewind, plus mixer pan and fader level. You can also monitor input levels, current time code, and battery status. With Zoom F8 Control, you can rename files, enter metadata, and set date/time information directly from your iOS device.

The hardware

Inputs

The F8 provides 8 discrete inputs with locking Neutrik XLR/TRS combo connectors. Each preamp has a dedicated gain control knob, a 6-segment LED level meter, and Record Ready and PFL switch. A 10-pin connector on the rear panel enables the use of Zoom mic capsules, with an optional extension cable that allows for remote positioning. There's also a built-in slate mic and a variable frequency slate tone generator to confirm levels.

Outputs

In addition to its ¼" headphone jack with dedicated volume control, the F8 provides four outputs: two Main Outs (on balanced TA3 mini-XLR jacks) for connection to external mixers and processing devices; and two Sub Outs (on a single unbalanced ⅛" stereo mini-jack) for connection to a camera.

Time code and USB

Time code I/O is provided on BNC connectors. A USB port enables firmware updates, file transfer, and allows the F8 to be used as an 8-in/4-out USB audio interface operating at sample rates up to 96 kHz.

The software

The F8's menu is easy to navigate and has a simple file structure. Cataloging is straightforward, with extensive metadata (both BEXT and iXML), which can be entered directly on the F8 or with the Zoom F8 Control App.

Onboard mixer

The F8's onboard mixer enables flexible signal routing from all inputs to all outputs, either pre- or post-fader, with user-adjustable level, pan, and input/output delay. In addition to advanced onboard limiters (which can be applied to all channels and tracks simultaneously), the F8 also provides high-pass filtering to reduce the sound of wind and other noise, plus phase inversion and Mid-Side decoding.

FEATURES

• 8-channel/10-track field audio recorder/mixer 
• 8 discrete inputs with locking Neutrik XLR/TRS combo connectors
• Compact and lightweight aluminum chassis, weighing just 2 pounds (without batteries)
• High quality mic preamps with up to 75 dB gain, less than -127 dBu EIN, and +4 dB line inputs
• Support for up to 24-bit/192 kHz recording as well as 96 kHz, 88.2 kHz, 48 kHz, and 44.1 kHz, plus 47.952 kHz/48.048 kHz for HD video compatibility; 16-/24-bit resolution
• Accurate Time Code (0.2 ppm) I/O on standard BNC connectors; dropframe/non-drop formats with Jam Sync
• Three different power supply options: 8x AA batteries, external DC battery pack with Hirose connector, or 12V AC adapter (AA’s and DC battery pack not included)
• Automatic switching of power source from DC to batteries at user-defined voltage levels
• Dedicated gain control knob, 6-segment LED level meter, and PFL/Solo switch for each channel
• Phantom power (+48V/+24V) on every preamp 
• Advanced onboard limiters for input and output
• High pass filter, phase invert, and Mid-Side decoder
• Input delay of up to 30 msec per channel / output delay of up to 10 frames per output
• Compatible with Zoom microphone capsules; optional extender cable enables remote positioning
• Dual mini-XLR (TA3) balanced Main Outs plus ⅛" stereo mini-jack Sub Out
• Dedicated headphone output (100 mW) with front panel volume control
• 2.4" full-color backlit LCD with monochrome mode
• Dedicated PFL display with viewable trim settings
• Dual SD/SDHC/SDXC card slots, up to 512 GB each 
• Records in BWF-compliant WAV or MP3 file formats
• Support for extensive metadata (BWF and iXML); input time, date, project, scene number, etc.
• Built-in slate mic/slate tone with front panel switch
• Built-in tripod mount; camera mount adapter also included
• Use as an 8-in/4-out USB audio interface (@ 96 kHz) 
• Free Zoom F8 Control App for iOS allows wireless remote control, file renaming, and metadata entry

Here's what comes included with the F8...

• Camera mount adapter
• Zoom AD-19 12V AC Adapter
• Operation manual
• TA3 to XLR cable x2
• Cubase LE and WaveLab LE download codes

Zoom PCF-8 Protective Case for F8 MultiTrack Field Recorders

The PCF-8 protective case is the perfect production accessory for the ZOOM F4 and ZOOM F8 MultiTrack Field Recorder. The lightweight and versatile bag offers top, side, and bottom access to the unit. With water-resistant construction and a removable clear-windowed cover, you can keep an eye on the bright F4/F8 screen without the risk of getting it wet or covered in dust.

Drawstring sleeves on the sides allow you to access your recorder's inputs and outputs while protecting them from the elements. You can keep accessories and connectors in the zippered front pouch and side pockets while storing mics and cables in the main compartment. The bottom of your F8 is accessible through a velcro flap underneath the bag, which can also be configured for additional cable routing.

The PCF-8 includes adjustable dividers that allow you to customize your bag to the way you use it. The main divider can be pulled out and inserted sideways, which forms a “table-top” surface for working with your F4/F8 in the open. Adjustable straps and three latch hooks per side allow you to comfortably carry your F4 or F8 on long shoots and roving sessions.

This protection/production case is custom made for the ZOOM F4 and F8 MultiTrack Field Recorders. It includes:

• Side openings with drawstring for XLR/TRS cable input and protection
• Detachable, water-resistant cover with clear window for  visual monitoring, plus inlay opening for personal notes
• Adjustable strap and shoulder pad combined with three latchhooks per side for a custom carry position
• Velcro inner divider which is removable to open up space or use as a table surface for F4 and F8 units
• Front and side pockets for extra storage
• Removable bottom panel to access rear of F4 and F8 units (BNC Time Code connectors, removable AA battery pack,and ZOOM mic capsule input)