Skip to content
SKU FUR-M-8S

Furman Power M-8S 15A Standard Power Conditioner with Sequencer M8S

Skip to the end of the images gallery
Skip to the beginning of the images gallery
Be the first to review this product
$429.95
Details More Information Reviews

General

  • Family: Merit Series
  • Line Voltage: 120 (Volts)
  • BlueBOLT Enabled: No
  • AC Protection
  • Automatic Voltage Shutoff: No

Shipping Info

  • Length: 21.9 (Inches)
  • Width: 9.4 (Inches)
  • Height: 3.4 (Inches)
  • Weight: 7.65 (Lbs)
  • Unit of Measure: Each
  • Master Pack Qty: 6

Other Specifications

  • Maximum AC Current Rating: 15 Amps, 120 VAC (Thermal breaker)
  • AC Cord: 14AWGx3, 10 feet, black, fixed, NEMA 5-15P plug
  • Convenience Outlet (Front Panel): 1 Un-switched NEMA 15-5R
  • Rear Panel Outlets: 2 Un-switched NEMA 5-15R (1 duplex)
  • 6 Sequenced NEMA 5-15R (3 duplexes, each controlled by separate relay)
  • AC Surge Protection: Merit Class (sacrificial)
  • Spike Protection Mode: Line to neutral, zero ground leakage
  • Max Continuous Operating Voltage: 130V RMS
  • Max Clamp Voltage: 500 Volts Peak
  • Peak Impulse Current: 12,000 Amps
  • Energy Rating (2 X 820µS): 225 Joules
  • AC Filtering: Pi LCR Filter
  • Noise Attenuation: >26dB, 100 Khz to 1 MHz
  • Operating Temperature Range: 5C (40F) to 40C (105F) degrees
  • Humidity Range: <90% rH (Relative Humidity)
  • Rocker Switch: Front panel, Sequence (ON, OFF)
  • Thermal Circuit Breaker: Front panel, push to reset
  • Front panel indicators: Delay 1, Delay 2, Delay 3, Power, Protection OK
  • Control/Status/Triggering (Rear Panel: Rear Panel DIP Switches: 12V Mode On/Off, GND Mode On, Momentary/Maintained
  • Potentiometer: Rear panel, time calibration fine tune delay adjust
  • Remote Terminal: +5-30VDC In, 12VDC (12mA) Out
  • Remote Terminal: Phoenix type 4-Pin Connector with Screw terminals; +12V, STAT, REM, GND (Class 2 Wiring)
  • Size: 1.75" X 19.00" X 6.5" (HWD) – ANSI 1RU
  • Mass: 5.3 lbs.
  • Power Consumption (No Load): 5 Watts
  • Safety Agency: C/CSA/US

Manufacturer's Description

Install an M-8S in your rack, and the eight outlets in the rear panel will power up in sequence and protect all your equipment up to a 15-amp load. Merit M-8S Power Sequencer is the perfect low-cost AC power solution for any rack mount system where power sequencing is desired. Install an M-8s in to the top slot of your rack, and the six delayed outlets in the rear panel will power up sequentially and protect all your equipment up to a 15-amp load. Includes 3 delayed outlet banks - each with 2 outlets - plus 2 unswitched outlets.

Features

  • Power Sequencing
    • Prevents excessive inrush currents.
    • Six sequenced rear panel outlets (in three groups), two unswitched rear panel outlets, and one front panel unswitched outlet.
    • Momentary and maintained sequencing via rear panel terminal block or front panel switch (momentary only).
  • Noise Filtration
    • Noise filtering to reduce radio frequency and electromagnetic interference.
  • Surge Protection
    • Ensures equipment stays safe.
  • 9 Total Outlets
    • Eight rear panel outlets and one front panel convenience panel outlet.
  • 15 Amp Rating
    • 15 amp rating, with circuit breaker.
  • "Protection OK" Indicator
    • Front panel indicator LEDs for Outlet Banks, Protection OK and Power Status.
  • Wall Wart SpacingAll settings and configurations available on rear panel.
    • Rear outlets have been spaced to accommodate even the bulkiest of wall warts and adapters.